Part Number

Picture

Price

Professor Motor High Performance and Service Parts

PMTR1046

$3.99

Professor Motor Chassis Lead - 0.035" (0.9mm) thick - 2 pcs. / package - each approximately  48mm x 75mm - high strength fiberglass reinforced adhesive backing - easily cut with scissors or sharp hobby knife - WARNING ! keep away from small children - this product contains a chemical known to the state of California to cause cancer, birth defects or other reproductive harm

To ORDER please click here to use our online shopping system

PMTR1047

$3.99

Professor Motor Chassis Lead - 0.016" (0.4mm) thick - 2 pcs. / package - each approximately  48mm x 75mm - high strength fiberglass reinforced adhesive backing - easily cut with scissors or sharp hobby knife - WARNING ! keep away from small children - this product contains a chemical known to the state of California to cause cancer, birth defects or other reproductive harm

To ORDER please click here to use our online shopping system

PMTR1052

$3.00

Pair of 1/32 Silicone lead wires (black/red) with high performance eyelet ends

To ORDER please click here to use our online shopping system

PMTR1053

$3.00

Pair of 1/32 Silicone lead wires (blue) with high performance eyelet ends

To ORDER please click here to use our online shopping system

PMTR1054

$3.00

Pair of 1/32 Silicone lead wires (yellow) with high performance eyelet ends

To ORDER please click here to use our online shopping system

PMTR1058

$8.00

Bulk 10 foot (305 cm) continuous spool of super flexible 1/32 high temp silicone lead wire (Red)

To ORDER please click here to use our online shopping system

PMTR1059

$8.00

Bulk 10 foot (305 cm) continuous spool of super flexible 1/32 high temp silicone lead wire (Black)

To ORDER please click here to use our online shopping system

PMTR1060

$8.00

Bulk 10 foot (305 cm) continuous spool of super flexible 1/32 high temp silicone lead wire (Yellow)

To ORDER please click here to use our online shopping system

PMTR1061

$8.00

Bulk 10 foot (305 cm) continuous spool of super flexible 1/32 high temp silicone lead wire (Blue)

To ORDER please click here to use our online shopping system

PMTR1062

$1.95

Package of 10 pcs. copper alloy 1.6mm diameter (slightly oversized for improved electrical connection & mechanical reliability) high performance eyelet ends for 1/32 lead wire

To ORDER please click here to use our online shopping system

PMTR1028

NEW !

$4.99

Professor Motor Neodymium traction magnet - for Slot.it "Race Magnet" application - ultra strong material - 24K Gold finish - "dogbone" shape to fit Slot.it HRS chassis - superglue or epoxy recommended for mounting  SAFETY WARNING ! - These small magnets are very powerful and can cause serious injury or death if swallowed - keep away from small children

To ORDER please click here to use our online shopping system

PMTR1115

NEW !

$3.99

Professor Motor Neodymium traction magnet - for NSR, Ninco & Early Scalextric applications - 24K Gold finish - 8mm diameter x 5mm tall  SAFETY WARNING ! - These small magnets are very powerful and can cause serious injury or death if swallowed - keep away from small children

To ORDER please click here to use our online shopping system

PMTR1116

NEW !

$12.99

Professor Motor Neodymium traction magnet assortment - 6 magnets total including "dogbone" Slot.it race magnet, 2 x 25x8x1mm, 2 x 10x6x2mm & 1 x 25x8x2mm - 24K Gold finish  SAFETY WARNING ! - These small magnets are very powerful and can cause serious injury or death if swallowed - keep away from small children

To ORDER please click here to use our online shopping system

PMTR1117

NEW !

$10.99

Professor Motor Neodymium traction magnet assortment - 7 magnets including 2 x 8mm diameter x 0.6mm, 1 x 8mm diameter x 5mm tall, 1 x 25x8x1mm, 1 x 25x7x1.5mm, & 1 x  19x6.1x1.5mm, 1 x8mm diameter x 2.7 mm tall - 24K Gold finish  SAFETY WARNING ! - These small magnets are very powerful and can cause serious injury or death if swallowed - keep away from small children

To ORDER please click here to use our online shopping system

PMTR1030

$3.00

Professor Motor Neodymium traction magnet - thin enough for under chassis mounting on most 1/32 cars - ultra strong material is particularly effective even though very thin when mounted under the chassis close to the track rails -  24K Gold finish - 25 x 8 x 1mm - SAFETY WARNING ! - These small magnets are very powerful and can cause serious injury or death if swallowed - keep away from small children

To ORDER please click here to use our online shopping system

PMTR1037

$3.50

Professor Motor Neodymium Traction Magnets - 6 Individual Ultra Thin, Ultra Strong Magnets per package - 24K Gold Finish - 0.6mm thick x 8mm diameter - ideal for applications where ground clearance is minimal.  SAFETY WARNING ! - These small magnets are very powerful and can cause serious injury or death if swallowed - keep away from small children

To ORDER please click here to use our online shopping system

PMTR1055

$3.00

Professor Motor Neodymium traction magnet - direct replacement for Scalextric & Slot.it SICN01 - 10+% stronger -  can be adapted to most 1/32 cars - 24K Gold finish - 25 x 8 x 2mm.  SAFETY WARNING ! - These small magnets are very powerful and can cause serious injury or death if swallowed - keep away from small children

To ORDER please click here to use our online shopping system

PMTR1056

$2.00

Professor Motor Neodymium traction magnet - direct replacement for TSRF TSC10 - 20+% stronger - can be adapted to most brands of 1/32 cars - thin enough to mount under chassis on most cars - 24K Gold plated finish - 19 x 6.1 x 1.5 mm  SAFETY WARNING ! - These small magnets are very powerful and can cause serious injury or death if swallowed - keep away from small children

To ORDER please click here to use our online shopping system

PMTR1057

$2.00

Professor Motor Neodymium traction magnet - direct replacement for Scalextric / Ninco / Fly Round Magnets - 20+% stronger - can be adapted to most brands of 1/32 cars - 24K Gold plated finish - 8mm outside diameter x 2.7 mm thick  SAFETY WARNING ! - These small magnets are very powerful and can cause serious injury or death if swallowed - keep away from small children

To ORDER please click here to use our online shopping system

PMTR1063

$2.50

Professor Motor Neodymium traction magnet - direct replacement for Pro Slot PS6001, 25% stronger -  fits most brands of 1/32 cars - thin enough to mount under chassis on many cars - 24K Gold finish - 25 x 7 x 1.5mm  SAFETY WARNING ! - These small magnets are very powerful and can cause serious injury or death if swallowed - keep away from small children

To ORDER please click here to use our online shopping system

PMTR1083

$3.50

Professor Motor Neodymium traction magnets - 2 / package - high strength secondary magnets for chassis tuning - can be adapted to most brands of 1/32 cars - 24K Gold finish - 10 x 6 x 2mm  SAFETY WARNING ! - These small magnets are very powerful and can cause serious injury or death if swallowed - keep away from small children

To ORDER please click here to use our online shopping system

PMTR1118

NEW !

$3.00

Professor Motor Neodymium traction magnet - narrow magnet ideal for placement ahead of rear axle in sidewinder and anglewinder applications -  fits most brands of 1/32 cars - 24K Gold finish - 27 x 5 x 1.5mm  SAFETY WARNING ! - These small magnets are very powerful and can cause serious injury or death if swallowed - keep away from small children

To ORDER please click here to use our online shopping system

PMTR1002

$2.49

Professor Motor hardened steel centerless ground 2 mm x 48mm long shafts for servicing any driveshaft equipped slot racing car.  Requires rotary tool with abrasive cutoff wheel or similar tool to cut to length.  Recommended installation -  support major length of shaft in vice and press pinion onto small section of shaft protruding from jaws of vice with small brass hammer and hollow tube or tool.  Cut shaft to length at end opposite pinion.

To ORDER please click here to use our online shopping system

PMTR1000

$9.95

Professor Motor HIGH PRECISION grade 3/32" (2.38mm) inside diameter ball bearings - stainless steel flanged double side shielded 3/16" (4.76mm) outside diameter - 2 bearings / package - for best results use PMTR1034 or Sloting Plus axles

To ORDER please click here to use our online shopping system

PMTR1114

$17.95

Professor Motor Double Flanged Double Side Shielded Stainless Steel HIGH PRECISION Ball Bearings for NSR 3/32" (undersize) axles - Snap Fits into Scalextric / Fly and other similar 1/32 car applications (same uses and Slot.it SIPA02 bushings) - For best results use only with NSR axles, gears and wheels - 2 bearings / package.

To ORDER please click here to use our online shopping system.

PMTR1012

$3.00

Professor Motor Axle Spacers - 0.010" (0.25mm) Thick Stainless Steel - fits 0.098" (2.5mm) or 3/32" (2.37mm) axle diameters - 16 pcs. / card - Use 2 minimum per side for low friction "thrust bearing" effect

To ORDER please click here to use our online shopping system.

PMTR1013

$3.00

Professor Motor Axle Spacers - 0.030" (0.76mm) Thick Nylon - fits 0.098" (2.5mm) or 3/32" (2.37mm) axle diameters - 16 pcs. / card

To ORDER please click here to use our online shopping system.

PMTR1029

$3.00

Professor Motor Axle Spacers - 0.005" (0.13mm) Thick Stainless Steel - fits 0.098" (2.5mm) or 3/32" (2.37mm) axle diameters - 16 pcs. / card - Use 2 minimum per side for low friction "thrust bearing" effect

To ORDER please click here to use our online shopping system.

PMTR1034

$1.99

Professor Motor drill blank axle 3/32" diameter x 57mm long.  Slightly smaller in diameter than the PMTR1069 axle for better fit in anodized aluminum wheels & can be used with the Slot.it RTR cars & Slot.it HRS chassis applications, gears and wheels.  Extra length is ideal for service of the Vanquish MG RTR cars.  This axle is used in our PMTR1028 Vanquish differential replacement kit.

To ORDER please click here to use our online shopping system.

PMTR1069

$1.99

High quality 3/32" diameter drill blank axle - 54 mm long - heat treated & centerless ground tool steel - made in Germany - Can be used with Slot.it bushings.  Not recommended for Slot.it HRS chassis applications or wheels & gears unless reamed to 3/32".

To ORDER please click here to use our online shopping system.

PMTR1087

$5.99

44 Tooth plastic setscrew sidewinder axle gear with aluminum hub for 3/32" axle - 64 pitch  super light weight, efficient and quiet gears for sidewinder or anglewinder application - 4mm overall width of hub & 0.718" (18.2mm) outside diameter - uses M2 metric setscrew & 0.9mm Allen wrench - use only with 64 pitch press-on pinion gears - click on the following link for possible gear ratios : link

To ORDER please click here to use our online shopping system.

PMTR1088

$5.99

45 Tooth plastic setscrew sidewinder axle gear with aluminum hub for 3/32" axle - 64 pitch  super light weight, efficient and quiet gears for sidewinder or anglewinder application - 4mm overall width of hub & 0.732" (18.6mm) outside diameter - uses M2 metric setscrew & 0.9mm Allen wrench - use only with 64 pitch press-on pinion gears - click on the following link for possible gear ratios : link

To ORDER please click here to use our online shopping system.

PMTR1089

$5.99

46 Tooth plastic setscrew sidewinder axle gear with aluminum hub for 3/32" axle - 64 pitch  super light weight, efficient and quiet gears for sidewinder or anglewinder application - 4mm overall width of hub & 0.748" (19mm) outside diameter - uses M2 metric setscrew & 0.9mm Allen wrench - use only with 64 pitch press-on pinion gears - click on the following link for possible gear ratios : link

To ORDER please click here to use our online shopping system.

PMTR1106

$5.99

47 Tooth plastic setscrew sidewinder axle gear with aluminum hub for 3/32" axle - 64 pitch  super light weight, efficient and quiet gears for sidewinder or anglewinder application - 4mm overall width of hub & 0.762" (19.4mm) outside diameter - uses M2 metric setscrew & 0.9mm Allen wrench - use only with 64 pitch press-on pinion gears - click on the following link for possible gear ratios : link

To ORDER please click here to use our online shopping system.

PMTR1078

$3.99

10 tooth steel 64 Pitch press-on motor pinion gears with precision counter-bore for easier installation - 2 gears / package - fits any standard 2mm diameter motor shaft - outside diameter 0.178" (4.52mm)

To ORDER please click here to use our online shopping system.

PMTR1079

$3.99

11 tooth steel 64 Pitch press-on motor pinion gear with precision counter-bore for easier installation - 2 gears / package - fits any standard 2mm diameter motor shaft - outside diameter 0.201" (5.11mm)

To ORDER please click here to use our online shopping system.

PMTR1080

$3.99

12 tooth steel 64 Pitch press-on motor pinion gear with precision counter-bore for easier installation - 2 gears / package - fits any standard 2mm diameter motor shaft - outside diameter 0.217" (5.51mm)

To ORDER please click here to use our online shopping system.

PMTR1103

$3.99

13 tooth brass 64 Pitch press-on motor pinion gear with precision counter-bore for easier installation - 2 gears / package - fits any standard 2mm diameter motor shaft - outside diameter 0.230" (5.84mm)

To ORDER please click here to use our online shopping system.

PMTR1104

$3.99

14 tooth steel 64 Pitch press-on motor pinion gear with precision counter-bore for easier installation - 2 gears / package - fits any standard 2mm diameter motor shaft - outside diameter 0.245" (6.22mm)

To ORDER please click here to use our online shopping system.

PMTR1105

$3.99

15 tooth steel 64 Pitch press-on motor pinion gear with precision counter-bore for easier installation - 2 gears / package - fits any standard 2mm diameter motor shaft - outside diameter 0.262" (6.65mm)

To ORDER please click here to use our online shopping system.

PMTR1065

$3.99

Brass 8 tooth metric spec pinion gears - package of 2 pcs.  Precision counter bored for easier installation.  Press fit to standard 2 mm motor shafts - by Professor Motor

To ORDER please click here to use our online shopping system.

PMTR1066

$3.99

Brass 9 tooth metric spec pinion gears - package of 2 pcs.  Precision counter bored for easier installation.  Press fit to standard 2 mm motor shafts - by Professor Motor - fits inline applications Fly, GB Track, Scalextric, Carrera, Slot.it

To ORDER please click here to use our online shopping system.

PMTR1067

$3.99

Brass 10 tooth metric spec pinion gears - package of 2 pcs.  Precision counter bored for easier installation.  Press fit to standard 2 mm motor shafts - by Professor Motor

To ORDER please click here to use our online shopping system.

PMTR1068

$3.99

Brass 11 tooth metric spec pinion gears - package of 2 pcs.  Precision counter bored for easier installation.  Press fit to standard 2 mm motor shafts - by Professor Motor - fits sidewinder applications Fly, GB Track, Scalextric, Slot.it

To ORDER please click here to use our online shopping system.

PMTR1077

$6.99

Brass Mixed Set of Metric Spec pinion gears - package of 1 each 8, 9, 10 & 11 tooth gears - precision counter bored for easier installation. Press fit to standard 2 mm motor shafts

To ORDER please click here to use our online shopping system.